[cpia] Aiptek HyperVcam Fun
Joseph C. Kopec
kopecjc@att.net
Sun, 16 Apr 2000 22:29:24 -0400
As mentioned in my earlier message, I have been having some problems
getting the Aiptek HyperVcam Fun webcam to operate, though it is
mentioned among the CPiA USB cameras on the webcam.sourceforge.net
site. Has anyone managed to get this to work under Linux with the cpia
software? When I boot up, I get the attached messages in dmesg --
basically, it says "usb.c: This device is not recognized by any
installed USB driver." One thing I noticed, is that it seemed that
usb-uchi and my ethernet port were both listed as using IRQ ll (and the
ethernet port worked fine) -- could this be causing the problem? Any
help would be much appreciated.
080
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: ganged power switching
hub.c: standalone hub
hub.c: global over-current protection
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port 1 is removable
hub.c: port 2 is removable
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface c11ba8a0
Linux NET4.0 for Linux 2.3
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Initializing RT netlink socket
Starting kswapd v1.6
parport0: PC-style at 0x378 [PCSPP]
pty: 256 Unix98 ptys configured
lp0: using parport0 (polling).
Linux video capture interface: v1.00
V4L-Driver for Vision CPiA based cameras v0.7.4
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 40MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller on PCI bus 00 dev a1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x20a0-0x20a7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x20a8-0x20af, BIOS settings: hdc:DMA, hdd:pio
hda: QUANTUM Bigfoot TX8.0AT, ATA DISK drive
hdc: COMPAQ DVD-ROM GD-2000, ATAPI CDROM drive
hdd: IOMEGA ZIP 100, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 15698592 sectors (8038 MB) w/69KiB Cache, CHS=1038/240/63
hdd: 196608 sectors (101 MB) w/16KiB Cache, CHS=512/12/32
hub.c: port 2 connection change
hdc: ATAPI 20X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.07
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 >
hdd:<7>hub.c: portstatus 101, change 1, High Speed
hub.c: portstatus 103, change 0, High Speed
usb.c: USB new device connect, assigned device number 2
usb.c: kmalloc IF c5fc7cc0, numif 1
usb.c: new device strings: Mfr=0, Product=0, SerialNumber=0
usb.c: unhandled interfaces on device
usb.c: This device is not recognized by any installed USB driver.
Length = 18
DescriptorType = 01
USB version = 1.00
Vendor:Product = 05a9:0511
MaxPacketSize0 = 8
NumConfigurations = 1
Device version = 1.00
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0089
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = 80
MaxPower = 500mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 01
bInterface Class:SubClass:Protocol = ff:00:00
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 01 (Isochronous)
wMaxPacketSize = 03e0
bInterval = 01
Alternate Setting: 1
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 01
bNumEndpoints = 01
bInterface Class:SubClass:Protocol = ff:00:00
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 01 (Isochronous)
wMaxPacketSize = 03e1
bInterval = 01
Alternate Setting: 2
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 02
bNumEndpoints = 01
bInterface Class:SubClass:Protocol = ff:00:00
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 01 (Isochronous)
wMaxPacketSize = 0300
bInterval = 01
Alternate Setting: 3
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 03
bNumEndpoints = 01
bInterface Class:SubClass:Protocol = ff:00:00
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 01 (Isochronous)
wMaxPacketSize = 0301
bInterval = 01
Alternate Setting: 4
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 04
bNumEndpoints = 01
bInterface Class:SubClass:Protocol = ff:00:00
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 01 (Isochronous)
wMaxPacketSize = 0200
bInterval = 01
Alternate Setting: 5
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 05
bNumEndpoints = 01
bInterface Class:SubClass:Protocol = ff:00:00
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 01 (Isochronous)
wMaxPacketSize = 0201
bInterval = 01
Alternate Setting: 6
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 06
bNumEndpoints = 01
bInterface Class:SubClass:Protocol = ff:00:00
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 01 (Isochronous)
wMaxPacketSize = 0101
bInterval = 01
Alternate Setting: 7
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 07
bNumEndpoints = 01
bInterface Class:SubClass:Protocol = ff:00:00
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 01 (Isochronous)
wMaxPacketSize = 0000
bInterval = 01
hdd4
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
scsi : 0 hosts.
scsi : detected total.
Serial driver version 4.93 (2000-03-20) with MANY_PORTS SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at port 0x02f8 (irq = 3) is a 16550A
PPP generic driver version 2.4.1
Linux Tulip driver version 0.9.4.2 (Mar 21, 2000)
eth0: Digital DS21143 Tulip rev 65 at 0x2000, 00:40:D0:00:C8:13, IRQ 11.
eth0: EEPROM default media type Autosense.
eth0: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2)
block.
eth0: Index #1 - Media 10baseT-FD (#4) described by a 21142 Serial PHY
(2) block.
PPP Deflate Compression module registered
[drm] Initialized tdfx 0.0.1 19991009 on minor 63
kmem_create: Forcing size word alignment - nfs_fh
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 164k freed
Adding Swap: 68000k swap-space (priority -1)